smbg5.0a thru smbg188ca www.vishay.com vishay general semiconductor revision: 12-nov-12 1 document number: 88456 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 surface mount t rans z orb ? transient voltage suppressors devices for bi-direction applications for bi-directional devices use ca suffix (e.g. smbg10ca). electrical characteristics apply in both directions. features ? low profile package ? ideal for automated placement ? glass passivated chip junction ? available in uni-directional and bi-directional ? 600 w peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % ? excellent clamping capability ? very fast response time ? low incremental surge resistance ? meets msl level 1, per j-st d-020, lf maximum peak of 260 c ? aec-q101 qualified ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 typical applications use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ics, mosfet, signal lines of sensor units for consumer, computer, industrial, automo tive, and telecommunication. mechanical data case: do-215aa (smbg) molding compound meets ul 94 v-0 flammability rating base p/n-e3 - rohs-compliant, commercial grade base p/nhe3 - rohs-complia nt, aec-q101 qualified terminals: matte tin plated leads, solderable per j-std-002 and jesd 22-b102 e3 suffix meets jesd 201 class 1a whisker test, he3 suffix meets jesd 201 class 2 whisker test polarity: for uni-directional types the band denotes cathode end, no marking on bi-directional types notes (1) non-repetitive current pulse, per fig. 3 and derated above t a = 25 c per fig. 2. (2) mounted on 0.2" x 0.2" (5.0 mm x 5.0 mm) copper pads to each terminal primary characteristics v wm 5.0 v to 188 v v br (uni-directional) 6.4 v to 231 v v br (bi-directional) 6.4 v to 231 v p ppm 600 w i fsm (uni-directional only) 100 a t j max. 150 c polarity uni-directional, bi-directional package do-215aa (smbg) do-215aa (smbg) maximum ratings (t a = 25 c unless otherwise noted) parameter symbol value unit peak pulse power di ssipation with a 10/1000 s waveform (1)(2) (fig. 1) p ppm 600 w peak pulse current with a 10/1000 s waveform (1) i ppm see next table a peak forward surge current 8.3 ms sing le half sine-wave uni-directional only (2) i fsm 100 a operating junction and storage temperature range t j , t stg - 55 to + 150 c
smbg5.0a thru smbg188ca www.vishay.com vishay general semiconductor revision: 12-nov-12 2 document number: 88456 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes (1) pulse test: t p ? 50 ms (2) surge current waveform per fi g. 3 and derate per fig. 2 (3) for bi-directional types having v wm of 10 v and less, the i d limit is doubled (4) all terms and symbols are cons istent with ansi/ieee c62.35 (5) for the bi-directional smbg/smbj5.8ca, the maximum v br is 7.25 v (6) v f = 3.5 v at i f = 50 a (uni-dir ectional only) (+) underwriters laboratory recognition for the classification of pr otectors (qvgq2) under the ul standard for safety 497b and fil e number e136766 for both uni-d irectional and bi-d irectional devices electrical characteristics (t a = 25 c unless otherwise noted) device type modified gull wing device marking code breakdown voltage v br at i t (1) (v) test current i t (ma) stand-off voltage v wm (v) maximum reverse leakage at v wm i d (a) (3) maximum peak pulse surge current i ppm (a) (2) maximum clamping voltage at i ppm v c (v) uni bi min. max. (+) smbg5.0a (5) ke ke 6.40 7.07 10 5.0 800 65.2 9.2 (+) smbg6.0a kg kg 6.67 7.37 10 6.0 800 58.3 10.3 (+) smbg6.5a kk ak 7.22 7.98 10 6.5 500 53.6 11.2 (+) smbg7.0a km km 7.78 8.60 10 7.0 200 50.0 12.0 (+) smbg7.5a kp ap 8.33 9.21 1.0 7.5 100 46.5 12.9 (+) smbg8.0a kr ar 8.89 9.83 1.0 8.0 50 44.1 13.6 (+) smbg8.5a kt at 9.44 10.4 1.0 8.5 20 41.7 14.4 (+) smbg9.0a kv av 10.0 11.1 1.0 9.0 10 39.0 15.4 (+) smbg10a kx ax 11.1 12.3 1.0 10 5.0 35.3 17.0 (+) smbg11a kz kz 12.2 13.5 1.0 11 5.0 33.0 18.2 (+) smbg12a le be 13.3 14.7 1.0 12 5.0 30.2 19.9 (+) smbg13a lg lg 14.4 15.9 1.0 13 1.0 27.9 21.5 (+) smbg14a lk bk 15.6 17.2 1.0 14 1.0 25.9 23.2 (+) smbg15a lm bm 16.7 18.5 1.0 15 1.0 24.6 24.4 (+) smbg16a lp lm 17.8 19.7 1.0 16 1.0 23.1 26.0 (+) smbg17a lr lr 18.9 20.9 1.0 17 1.0 21.7 27.6 (+) smbg18a lt bt 20.0 22.1 1.0 18 1.0 20.5 29.2 (+) smbg20a lv lv 22.2 24.5 1.0 20 1.0 18.5 32.4 (+) smbg22a lx bx 24.4 26.9 1.0 22 1.0 16.9 35.5 (+) smbg24a lz bz 26.7 29.5 1.0 24 1.0 15.4 38.9 (+) smbg26a me ce 28.9 31.9 1.0 26 1.0 14.3 42.1 (+) smbg28a mg mg 31.1 34.4 1.0 28 1.0 13.2 45.4 (+) smbg30a mk ck 33.3 36.8 1.0 30 1.0 12.4 48.4 (+) smbg33a mm cm 36.7 40.6 1.0 33 1.0 11.3 53.3 (+) smbg36a mp cp 40.0 44.2 1.0 36 1.0 10.3 58.1 (+) smbg40a mr cr 44.4 49.1 1.0 40 1.0 9.3 64.5 (+) smbg43a mt ct 47.8 52.8 1.0 43 1.0 8.6 69.4 (+) smbg45a mv mv 50.0 55.3 1.0 45 1.0 8.3 72.7 (+) smbg48a mx mx 53.3 58.9 1.0 48 1.0 7.8 77.4 (+) smbg51a mz mz 56.7 62.7 1.0 51 1.0 7.3 82.4 (+) smbg54a ne ne 60.0 66.3 1.0 54 1.0 6.9 87.1 (+) smbg58a ng ng 64.4 71.2 1.0 58 1.0 6.4 93.6 (+) smbg60a nk nk 66.7 73.7 1.0 60 1.0 6.2 96.8 (+) smbg64a nm nm 71.1 78.6 1.0 64 1.0 5.8 103 (+) smbg70a np np 77.8 86.0 1.0 70 1.0 5.3 113 (+) smbg75a nr nr 83.3 92.1 1.0 75 1.0 5.0 121 (+) smbg78a nt nt 86.7 95.8 1.0 78 1.0 4.8 126 (+) smbg85a nv nv 94.4 104 1.0 85 1.0 4.4 137 (+) SMBG90A nx nx 100 111 1.0 90 1.0 4.1 146 (+) smbg100a nz nz 111 123 1.0 100 1.0 3.7 162 (+) smbg110a pe pe 122 135 1.0 110 1.0 3.4 177 (+) smbg120a pg pg 133 147 1.0 120 1.0 3.1 193 (+) smbg130a pk pk 144 159 1.0 130 1.0 2.9 209 (+) smbg150a pm pm 167 185 1.0 150 1.0 2.5 243 (+) smbg160a pp pp 178 197 1.0 160 1.0 2.3 259 (+) smbg170a pr pr 189 209 1.0 170 1.0 2.2 275 smbg188a ps ps 209 231 1.0 188 1.0 2.0 328
smbg5.0a thru smbg188ca www.vishay.com vishay general semiconductor revision: 12-nov-12 3 document number: 88456 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) mounted on minimum recommended pad layout note (1) aec-q101 qualified ratings and characteristics curves (t a = 25 c unless otherwise noted) fig. 1 - peak pulse power rating curve fig. 2 - pulse power or current vs. initial junction temperature fig. 3 - pulse waveform fig. 4 - typical junction capacitance thermal characteristics (t a = 25 c unless otherwise noted) parameter symbol value unit typical thermal resistance , junction to ambient (1) r ? ja 100 c/ w typical thermal resistance, junction to lead r ? jl 20 ordering information (example) preferred p/n unit weight (g) preferred pa ckage code base quantity delivery mode smbg5.0a-e3/52 0.096 52 750 7" diam eter plastic tape and reel smbg5.0a-e3/5b 0.096 5b 3200 13" diam eter plastic tape and reel smbg5.0ahe3/52 (1) 0.096 52 750 7" diameter plastic tape and reel smbg5.0ahe3/5b (1) 0.096 5b 3200 13" diameter plastic tape and reel 0.1 1 10 100 0.2 x 0.2" (5.0 x 5.0 mm) copper pad areas p ppm - peak p u lse po w er (k w ) t d - p u lse w idth (s) 0.1 s 1.0 s 10 s 100 s 1.0 ms 10 ms 0 255075100 100 75 50 25 0 125 150 175 200 t j - initial temperat u re (c) peak p u lse po w er (p pp ) or c u rrent (i pp ) derating in percentage, % 0 50 100 150 t d 0 1.0 2.0 3.0 4.0 i ppm - peak p u lse c u rrent, % i rsm t - time (ms) t r = 10 s peak val u e i ppm half val u e - i ppm i pp 2 10/1000 s w a v eform as defined by r.e.a. t j = 25 c p u lse w idth (t d ) is defined as the point w here the peak c u rrent decays to 50 % of i ppm 10 100 1000 6000 10 1 100 200 uni-directional bi-directional t j = 25 c f = 1.0 mhz v sig = 50 mvp-p meas u red at zero bias v r , meas u red at stand-off voltage v w m c j - j u nction capacitance (pf) v w m - re v erse stand-off voltage (v)
smbg5.0a thru smbg188ca www.vishay.com vishay general semiconductor revision: 12-nov-12 4 document number: 88456 for technical questions within your region: diodesamericas@vishay.com , diodesasia@vishay.com , diodeseurope@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 5 - typical transient thermal impedance fig. 6 - maximum non-repetitive peak forward surge current package outline dimensions in inches (millimeters) 0.1 1.0 10 100 0.001 0.01 0.1 10 1 100 1000 t p - p u lse d u ration (s) transient thermal impedance (c/ w ) 10 200 100 1 100 10 nu mber of cycles at 60 hz peak for w ard s u rge c u rrent (a) 8.3 ms single half sine- w a v e uni-directional only 0.180 (4.57) 0.160 (4.06) 0.016 (0.41) 0.006 (0.15) 0.020 (0.51) max. 0.058 (1.47) 0.038 (0.97) 0.255 (6.48) 0.235 (5.97) 0.030 (0.76) 0.015 (0.38) 0.155 (3.94) 0.130 (3.30) 0.083 (2.10) 0 .077 (1.96) 0.095 (2.41) 0.075 (1.90) 0.165 (4.19) 0.085 (2.16) 0.060 (1.27) do-215aa (smbg) mounting pad layout cathode band 0.008 (0.20) 0.002 (0.05) seating plane
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
